Are you looking for solutions to solve your Ooma station blinking red? Remain calm. You understood this post. To resolve the problem, you might attempt a few troubleshooting techniques.
Your Ooma station is not connecting to the network if it is glowing red.
There are several possible causes. For example, this could be the result of a little bug on the gadget.
Here are a few fast fixes for the problem. Make sure the device has been properly activated first. Try using the cable on a different port and restarting the station as well. In summary, these are the troubleshooting pointers.This post provides a detailed explanation of the red blinking on your Ooma equipment. The post’s last section provides troubleshooting advice to resolve the issue.
Reasons Why Ooma Is Blinking Red
As previously indicated, a sign that the Ooma device is not connected to the network is its red flashing status. The following are a few explanations for that:
Device Not Fully Activated:
There are two possible outcomes if the gadget is glowing red when you use it for the first time after setup. It can be the case that the gadget is not fully activated or that there was a configuration problem. The Ooma station may fail to establish an internet connection due to one of these issues.
Glitch
The device may display a red hue that is steady or blink red due to a glitch. In either case, unless the issue is resolved, the Ooma won’t be able to connect to the internet.
Bad Cable
An additional explanation can be a malfunctioning Ethernet cable connecting the Ooma device to the Ethernet hub. Over time, the cable may experience mechanical stress that could lead to this.
Issue With Port
Lastly, the Ethernet port itself may be the source of the problem. One possibility is that the port on the Ethernet wire is broken.
Troubleshooting Tips To Fix Ooma Is Blinking Red Issue
Now that you are aware of the potential causes of your Ooma device’s red blinking, let’s look at some troubleshooting techniques to get it operating once more.
Complete Activation Process
As previously indicated, the device is not fully activated if you have just finished the setup and activation process and it is blinking red. There might be a problem with the activation procedure.
Restarting the activation process is the best method to resolve this. Go to the Ooma manual page. Click your device to see the setup instructions. To finish the setup and activation process, adhere to the instructions.
If the problem still exists even after you have finished the activation process, try the alternative troubleshooting methods listed below.
Power Cycle Ooma Device
A power cycle is when the gadget is turned off by force. This simple procedure will resolve any issues with the Ooma station.
Unplug the power cable from the Ooma station and router in order to power cycle your device. After 60 seconds, unplug the cord and wait again.
Permit the gadgets to restart. Await the light turning blue for five minutes.
Switch Ports
The Ethernet wire that joins your Ethernet hub and Ooma station should be unplugged. Connect the cord to an alternate Ethernet hub port.
Change Ethernet Cable
Swapping out the Ethernet wire itself is an additional choice. It is possible that the wire is frayed if you have been using it for a long time. Changing to a new Ethernet cable might be all that is required to resolve the problem.
Factory Reset Ooma Device:
Resetting the Ooma station device to factory defaults is the last resort. Only carry out a factory reset when absolutely required. In order to factory reset your device, follow these steps:
Re-plug the Ooma station’s power cable after unplugging it.
.. Await the lights turning on and the gadget rebooting.
Hold down both the Play and Trash buttons at the same time for 60 seconds. On certain power stations, the buttons could show up as stop (square) and trash buttons.
.. Give the buttons a release. Give the Ooma station five minutes to reboot.
You might need to adjust the configuration parameters following a factory reset.
Contact Ooma Customer Support:
It’s time to get in touch with Ooma tech support if you’ve tried every suggestion and none of them has worked thus far. For assistance, call 1-866-939-662 in the US or 1-877-948-6662 in Canada.
The tech support agent will advise you on further actions to take in order to resolve the problem. This can entail sending the Ooma station back to be fixed or replaced by mail.